Kitfox Aircraft Stick and Rudder Stein Air Grove Aircraft TCW Technologies Dynon Avionics AeroLED MGL Avionics Leading Edge Airfoils Desser EarthX Batteries Garmin G3X Touch
Results 1 to 10 of 26

Thread: Fuel Filter Advice

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    SWeidemann's Avatar
    Join Date
    Nov 2009
    Location
    Madison, WI
    Posts
    159

    Default Fuel Filter Advice

    Kitfox Folks,

    I'm looking for testimonials and field experience about fuel filters. What type & brand of fuel filter do people use and why? My latest favorite is the bronze filter element that can be installed in the engine compartment if desired (or anywhere else) and can be removed for inspection and cleaning, such as Earl's aluminum body with bronze insert. I have a technical bias against paper elements however they are being widely used. What do others use?

    Thanks much,

    Skot
    Kitfox Vixen 912 ULS
    N24V at C29

  2. #2
    Senior Member t j's Avatar
    Join Date
    Oct 2009
    Location
    Ellensburg, WA
    Posts
    863

    Default Re: Fuel Filter Advice

    I have a finger strainer in each fuel tank and a 120 micron screen in my Aircraft spruce gascolator. That's all.

    The Rotax 2 stroke installation manual says don't use paper filters. Use a fuel filter of 0.15mm (150 microns).
    Tom Jones
    Classic 4 builder

  3. #3
    Senior Member HighWing's Avatar
    Join Date
    May 2009
    Location
    Goodyear, AZ
    Posts
    1,743

    Default Re: Fuel Filter Advice

    I have glass fuel filters mounted in the down lines from each wing tank to the header tank. My lines run down along the top of the quarter window. The filters are visible as I fly and in low fuel situations as in long down runs from the Sierra crossing to home, I can visibly monitor fuel flow. I also have the finger strainers in the tanks. 900 hours on the first Model IV with this set-up and not a hiccup.

    I do have one of the filters you describe, but it came with my second hand kit and it is still in the box as I like to see what is going on without taking things apart.
    Lowell Fitt
    Goodyear, AZ


    My You Tube Channel

  4. #4
    Senior Member
    Join Date
    Jul 2013
    Location
    Highlands Ranch, CO
    Posts
    404

    Default Re: Fuel Filter Advice

    My preference is a combination of both Lowells and Toms.

    I like the visibility aspect of Lowells and it provides the ability to supply fuel if one filter becomes clogged.

    I believe a gascolator is necessary, but I do remove the mesh inlet filter as no need to filter twice.

    A few other points to ponder:

    Rotax recommends a 100 micron (.1mm) for 4 strokes. Most would find anything between 70 and 100 micron acceptable. Any finer and you are increasing the probability of clogging and the required maintenance un-necessarily.

    I agree paper filters should be avoided - most are far finer than 100 micron and can clog much faster and trap water much easier. It is beyond me why places like Aircraft Spruce even sell them.

    I would also never use a plastic or glass filter housing in the engine bay.

    If using electric fuel pump(s) many have a pre-filter built into the inlet (ala 914 Pierburg pump). If you have an electric pump chances are it has one and it may be required by the pump manufacturer - it is another maintenance item.

    If you have another type of fuel system - IE injected - follow the manufacturers recommendations to a tee. Many injectors require much finer filtering than a carbureted engine.

    Incorrect filter micron selection/maintenance may be the cause of some rough running installations. How many even know the micron size of their filters?

    All IMHO, YMMV!
    Greg

  5. #5
    Senior Member jiott's Avatar
    Join Date
    Jun 2010
    Location
    Portland, OR
    Posts
    2,972

    Default Re: Fuel Filter Advice

    I use the filter provided in the factory SS7 FWF kit for the 912. It is a NAPA inline filter in a metal housing, mounted at the inlet to the fuel pump per the build manual. Finger strainers are also include in the outlet of each fuel tank.

    I personally don't believe a gascolator is necessary (neither does the factory) because you don't need to filter twice and the header tank with its drain at the lowest point in the system does the same job as a gascolator for water separation/draining.
    Jim Ott
    Portland, OR
    Kitfox SS7 flying
    Rotax 912ULS

  6. #6
    kitfoxnick's Avatar
    Join Date
    Jun 2008
    Location
    Northeastern, MD
    Posts
    199

    Default Re: Fuel Filter Advice

    My setup is very similar to Lowell's. I have two glass filters visible through the turtle deck. These filters can be taken apart and cleaned. I like being able to monitor the fuel and contamination level.
    Nick W
    IV 1200
    912Ul
    Warp Taper Tip

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •