Kitfox Aircraft Stick and Rudder Stein Air Grove Aircraft TCW Technologies Dynon Avionics AeroLED MGL Avionics Leading Edge Airfoils Desser EarthX Batteries Garmin G3X Touch
Page 6 of 10 FirstFirst ... 2345678910 LastLast
Results 51 to 60 of 91

Thread: Kitfox Factory Fly-in 2013

  1. #51
    Senior Member SkySteve's Avatar
    Join Date
    Jun 2008
    Location
    Huntsville, UT
    Posts
    1,054

    Default Re: Kitfox Factory Fly-in 2013

    Jamesmil,
    Love it! Bend over and cough real loud, maybe that will help with the medical condition
    Last edited by SkySteve; 09-10-2013 at 09:22 PM.
    Steve Wilson
    Huntsville, UT
    Kitfox 85DD
    912A / 3 Blade Taper Tip Warp Drive
    Convertible Nosewheel & Tailwheel
    SkySteve's SPOT Page
    SkySteve's You Tube Videos

  2. #52
    Senior Member SkyPirate's Avatar
    Join Date
    Apr 2009
    Location
    Edgar Springs MO
    Posts
    1,841

    Default Re: Kitfox Factory Fly-in 2013

    it was 96 here on the ground in MO when you flew thru,..I was wondering if it was bumpy or not,..sounds like it may have been ??

  3. #53
    Senior Member
    Join Date
    Feb 2011
    Location
    wilmington nc
    Posts
    201

    Default Re: Kitfox Factory Fly-in 2013

    yes skypirate it was hot and bumpy. had to get to 6500 before it cooled down. setting in the hotel room looking out the window at the rain and low ceilings. the weathers not looking good for today or tomorrow, might try to reposition north if I get a break in the weather later today.

  4. #54
    Senior Member
    Join Date
    Feb 2011
    Location
    wilmington nc
    Posts
    201

    Default Re: Kitfox Factory Fly-in 2013

    well this sucks, still stuck in Cheyenne. the weather is still bad and forecast to stay about the same for the next 2 days and then it looks like it's not going to all that good in Idaho. I hate to say it but if it's the same tomorrow I might see if I can get a svfr out of here and follow 80 east till I get to better weather. then i'll decide what to do.

  5. #55
    Senior Member SkyPirate's Avatar
    Join Date
    Apr 2009
    Location
    Edgar Springs MO
    Posts
    1,841

    Default Re: Kitfox Factory Fly-in 2013

    It looks like its rotation is pulling it north

  6. #56
    Senior Member SkySteve's Avatar
    Join Date
    Jun 2008
    Location
    Huntsville, UT
    Posts
    1,054

    Default Re: Kitfox Factory Fly-in 2013

    Jamesmil,
    The weather in Ogden has been low clouds and rain much of today. Clouds are breaking up, the rain has stopped and the sun is out now. I have no idea what tomorrow will bring. They are saying more rain but that is likely to come later in the day. I'll make a go, no-go decision in the morning for tomorrow's launch. If it's raining in the morning I'll wait until we get a break, either late morning or early afternoon. If its not good by then I will plan on an early departure Fri morning.
    Steve Wilson
    Huntsville, UT
    Kitfox 85DD
    912A / 3 Blade Taper Tip Warp Drive
    Convertible Nosewheel & Tailwheel
    SkySteve's SPOT Page
    SkySteve's You Tube Videos

  7. #57
    Senior Member SkyPirate's Avatar
    Join Date
    Apr 2009
    Location
    Edgar Springs MO
    Posts
    1,841

    Default Re: Kitfox Factory Fly-in 2013

    Sheridan looks clear and you might have a tail wind
    Last edited by SkyPirate; 09-11-2013 at 04:19 PM.

  8. #58
    Senior Member SkyPirate's Avatar
    Join Date
    Apr 2009
    Location
    Edgar Springs MO
    Posts
    1,841

    Default Re: Kitfox Factory Fly-in 2013

    The moderate turbulence starts at 27000 msl so your good there, looks like a small squal line if you draw a line from boise to sheridan its about 1/2 way and following the line

  9. #59
    Senior Member SkyPirate's Avatar
    Join Date
    Apr 2009
    Location
    Edgar Springs MO
    Posts
    1,841

    Default Re: Kitfox Factory Fly-in 2013

    I guess what im saying is i agree with you as far as clear north, as for terrain, i do not know, if you could fly north east toward alliance and then turn north toward pine ridge , when you hit route 20 turn west toward sheridan then stay north of the convection until your near boise

  10. #60
    Senior Member SkyPirate's Avatar
    Join Date
    Apr 2009
    Location
    Edgar Springs MO
    Posts
    1,841

    Default Re: Kitfox Factory Fly-in 2013

    There is one restricted area 7001a,b,c ground to 30,000. Its tough to tell exactly where, im looking at 3 different programs , but its between KCPR and KCYS, slightly north east of center between them
    I think you might be north west of that restricted area from where your at
    Last edited by SkyPirate; 09-11-2013 at 05:01 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •