Kitfox Aircraft Stick and Rudder Stein Air Grove Aircraft TCW Technologies Dynon Avionics AeroLED MGL Avionics Leading Edge Airfoils Desser EarthX Batteries Garmin G3X Touch
Results 1 to 10 of 10

Thread: H-Stab Electric Actuator Adjustment

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    N14ND's Avatar
    Join Date
    Oct 2008
    Location
    Graham, WA
    Posts
    113

    Default H-Stab Electric Actuator Adjustment

    Been trying to set my Series 5 (newer style actuator) stabilizer actuator travel (first time) and not having any luck using the directions in Chapter X, "Rigging of Flight Controls", page 40-41, steps 33-34. Also, I have read and attempted the different threads on this forum concerning same, which are basically, the steps in the manual.

    The longest actuator length, fully extended (aircraft nose down), with the rod end and jamb nut screwed completely into the actuator; the horizontal stab tube and the fuselage tube hit (binding the actuator). If I take the jamb nut off and screw the rod end all the way into the actuator, then there is about 1/4" of clearance between the tubes. This has been the only way that I have been able to have any clearance without binding the actuator. There is no way I will be able to get the 7/16" clearance.

    There is no way to adjust the stroke of the actuator, despite what the manual says. The manual states, "As the shaft is rotated, stroke of the actuator will be shortened if the rotation is clockwise". That does not work with the actuator I have. I have not be able to replicate this. Disconnecting the links and the rod end from the stab, rotating the actuator shaft "clockwise" until the correct distance between the tubes is correct, then reconnecting everything....once the actuator is run full travel down and back up, it is once again tube-to-tube contact.

    I have tried numerous combinations of things. None work. The actuator shaft stroke is what it is, there is no way to shorten it. The only adjustment is the rod end. Which leaves me in a bind....

  2. #2
    N14ND's Avatar
    Join Date
    Oct 2008
    Location
    Graham, WA
    Posts
    113

    Default Re: H-Stab Electric Actuator Adjustment

    Went out again this morning and tried the procedures a couple more times. Just incase the 10 or so times I did it last night were different. No change. I removed the actuator and measured the stroke from the lower pivot to the top of the actuator (with rod end removed):

    Extended: 19.250"
    Retracted: 15.375"

    Stroke travel is: 3.875"

    Don't know the correct length.

  3. #3
    Senior Member jiott's Avatar
    Join Date
    Jun 2010
    Location
    Portland, OR
    Posts
    2,959

    Default Re: H-Stab Electric Actuator Adjustment

    You can't change the stroke range of the actuator-don't try. What you can change is the distance the actuator rod sticks out of the tube, but the stroke range will remain the same. Just disconnect the links to the rod and screw it into or out of the tube until you get what you want, then reconnect the links. Will probably take several tries. Trust us, it does work. You do have some fine adjustment available by screwing the spherical rod end in or out, but that is not the main method of adjustment. I suggest screwing the rod end in to some middle point and then lock the jam nut and leave it there.
    Jim Ott
    Portland, OR
    Kitfox SS7 flying
    Rotax 912ULS

  4. #4
    Senior Member jtpitkin06's Avatar
    Join Date
    Jan 2010
    Location
    Greenville, TX
    Posts
    640

    Default Re: H-Stab Electric Actuator Adjustment

    This subject has popped up before as the instructions do not outline what you are doing beforehand.

    The only adjustment to the actuator total length is via the ROD END. The actuator will always run full up and full down and the actuator shaft extended length is not adjustable.

    Prior to doing adjustments, the horizontal stab is mounted in the fuselage with the actuator attached at both ends.

    The manual instructs you screw the ROD END all the way into the actuator.

    There are two ways to do this.

    You can disconnect the rod end and scissors from the horizontal stab and risk dropping all the shims, washers, nut and bolt into a hard to reach location; and, have the horizontal stab fall on your head while you try to make adjustments. OR…

    Disconnect only the scissor link keeping the rod end connected to the stab. The actuator will support the horizontal stab while you do the trial and error adjustments.

    Next, loosen the rod end jam nut and rotate the actuator shaft counter-clockwise to screw the rod end all the way into the shaft. Turning the actuator shaft counter-clockwise will screw the rod end inward. Simple and you don’t drop parts.

    Temporarily connect the scissor (use a rubber band) and apply power to run the actuator out full length. ( a small 9 volt battery will do this just fine) Now measure the clearance between the fuselage and the horizontal stab. The setting is 7/16 +/- 1/16. If your horizontal stab is hitting the fuselage you have the wrong rod end installed, the rod end in the wrong holes, (it goes in the forward holes) or the rod end is not screwed in all the way.

    To make adjustments you disconnect the scissor and rotate the actuator shaft. Rotating the shaft changes the rod end extension but also screws the actuator in or out at the same time. Because the actuator length temporarily changes you must apply power again to extend the actuator to full length. It takes a few tries to get it right.

    When the adjustment is correct, lock the rod end with the jam nut and permanently attach the scissor link.

    Just for reference my actuator compressed length from hole to hole is 15.50 inches. and the extended length is 19.675 inches.

    One final note: Screwing the actuator shaft in or out manually never changes the stroke or end points. Only the rod end extension changes the total length.

    John Pitkin
    Greenville, TX

  5. #5
    Senior Member jiott's Avatar
    Join Date
    Jun 2010
    Location
    Portland, OR
    Posts
    2,959

    Default Re: H-Stab Electric Actuator Adjustment

    You are correct John; I was remembering wrong.
    I'm not sure why N14ND is having trouble with the actuator being too long even with the rod end all the way in. Must be something to do with the mounting of the bottom end of the actuator, or the H stab.
    Jim Ott
    Portland, OR
    Kitfox SS7 flying
    Rotax 912ULS

  6. #6
    N14ND's Avatar
    Join Date
    Oct 2008
    Location
    Graham, WA
    Posts
    113

    Default Re: H-Stab Electric Actuator Adjustment

    Thanks John, I have read your instructions in a previous thread. And followed it... doesn't work for this installation. Basically, impossible to get the actuator any shorter in length (p/n 61012.101). Don't know if the newer actuators are shorter. Yes, I have it installed correctly into the correct hole on the h-stab tab. Pretty hard to get the scissors to work correctly on the aft side of the actuator otherwise. There is only one location at the lower fuselage pivot. Yes, I have the correct rod end (supplied with actuator) installed with p/n 10001.116 bushing pressed in, AN316-4 (thin) check nut in installed. With the rod end and check nut screwed in all the way in as far as it will go into the actuator (bottomed out) actuator length from hole-to-hole is:

    fully extended 20.00"
    retracted (compressed) 16.00".

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •