Supporting vendors:
 
Your ad here?
 
Old 04-30-2018, 10:58 AM   #21
mscotter
 
Join Date: Nov 2010
Location: Winston-Salem, NC
Posts: 38
Default Re: #Northernfox Build

you could always buy a sandblasting rig and start doing it yourself. I think you can get them from harbor freight. Not challenging, just tedious...
mscotter is offline   Reply With Quote
Old 04-30-2018, 11:54 AM   #22
efwd
Senior Member
 
efwd's Avatar
 
Join Date: Jun 2015
Location: Yorba Linda, CA
Posts: 1,508
Default Re: #Northernfox Build

if you have some MEK on hand, it will clear paint from the surface with little effort. try it out and see what it is exactly that your looking at underneath. Then, I would do the sandblaster from Harbor Freight myself if the airframe looked unscathed under that paint removed with MEK.
Eddie
efwd is online now   Reply With Quote
Old 06-08-2018, 12:43 PM   #23
tracstarr
 
Join Date: Dec 2017
Location: Canada
Posts: 120
Default Re: #Northernfox Build

Well, two bits of news that's exciting for me.

1- got my shipment from Kitfox with my FFW, LLE and some other bits I needed.

2 - finally (as in yesterday) found someone who is willing and able to take on the blasting and powder coating of my frame. He's done some air frames in the past. Excited to get going on this now.

I guess my next post will be dis-assembly of the entire fuselage which was complete. Oh well.
tracstarr is offline   Reply With Quote
Old 07-09-2018, 11:54 AM   #24
tracstarr
 
Join Date: Dec 2017
Location: Canada
Posts: 120
Default Re: #Northernfox Build

So, a few small updates. Sorry, no pics.

As posted here and in my last post here - I had to tear down my fuselage to prep for sandblasting.

I managed to get the vertical stabilizer ribs off without too much damage using a heat gun. They should be re-usable if I can clean them up without damaging them.

Everything else came off easily and I taped up the long aluminum stringers on the sides and bottom of the body. I also left the aluminum door frame pieces on.

It finally got blasted over the weekend after sitting in the shop for about 3 weeks.

Turns out - those flimsy aluminum pieces warp pretty easily with blasting (from just the heat). So, the shop took them off as well as the stringers. No big deal, i'll have to re-make them.

All that said, the blasting went well and all welds were perfect. No cracks no rust no anything found under all that junk. Needless to say I am very very happy to know this - and the blasting and re-coat is well worth it.
tracstarr is offline   Reply With Quote
Old 07-09-2018, 12:49 PM   #25
DesertFox4
Administrator
 
DesertFox4's Avatar
 
Join Date: Aug 2008
Location: Phoenix,AZ
Posts: 2,728
Default Re: #Northernfox Build

Glad to read after all that effort that the tubing and welds are in good condition.
You can now move forward with piece of mind you are building on a solid foundation.
__________________


DesertFox4
Admin.
Building 7 Super Sport
912 ULS Tri-gear
DesertFox4 is offline   Reply With Quote
Old 07-09-2018, 02:22 PM   #26
aviator79
Senior Member
 
aviator79's Avatar
 
Join Date: Dec 2016
Location: Los Alamos, NM
Posts: 591
Default Re: #Northernfox Build

Quote:
Originally Posted by DesertFox4 View Post
You can now move forward with piece of mind you are building on a solid foundation.
Peace of mind is priceless.

...actually, you probably know the price to the nearest penny right now.

I'm glad you can get on with it now. It'll feel much better going forward with the uncertainty resolved.
__________________
--Brian
Building SS7
aviator79 is offline   Reply With Quote
Old 09-19-2018, 04:45 PM   #27
tracstarr
 
Join Date: Dec 2017
Location: Canada
Posts: 120
Default Re: #Northernfox Build

Been a little while - I'm sure you all know how it goes (or doesn't) sometimes.

So my story continues with the pickup of my newly coated frame. Oh man I was happy with it. Absolutely amazing work. Shout out to Performance Finishing & Fabrication Inc in Vars Ontario Canada!

Got her back to my shop and just caressed her for a while. Well worth it!

The next steps after that was many many evenings sorting through the boxes of parts that came with it. It was a total disaster. Many parts had no labels (worn away by years of sitting there) and some were rusted out. Good thing is they are all easily replaceable... bad thing is I have no idea what they are and what to get.

I just started pinning things the the wall under different groups when I figure out what they were. Part of the problem with a partially built kit (in my case) was it was pretty hard to determine what parts were used and what parts I should be hoping to find without reading every single page. And I did. It only helped a little.

So after a few nights of that I figured it was time to move on and wing it as I went.

Life then got in the way for a few weeks.

I was able to in that time take measurements of all the completed wing assembly to make sure it was all within spec as it was not a factory built wing. Everything looked good and was off in only a few places by about 1/8". About the biggest find was only 4/5 rivets in each of the drag/anti-drag attachments. I should be able to get one more in.

Finally back at it this week with some help. Ordered up a bunch of missing items from kitfox on day one - and some of the consumables I'm going to need.

Today with some help again we leveled up the fuselage and mounted the wings to verify dihedral, sweep, washout and wing twist. With only a small adjustment everything looked near perfect.

From there since we have to wait on some hysol, we got the firewall setup and test fit the engine mount and got that hardware all test fit.

Feels good to really get some progress going.
tracstarr is offline   Reply With Quote
Old 09-20-2018, 05:42 PM   #28
tracstarr
 
Join Date: Dec 2017
Location: Canada
Posts: 120
Default Re: #Northernfox Build

Today was more progress. Took apart the pedal assembly and found it needs to be greased. Put them back in, got all the connections done and control sticks in. They'll be coming out again for re-paint eventually.

One of the modifications done today was to use riv-nuts for the pedal attachments to the frame. This will allow easy removal for future inspection etc.
tracstarr is offline   Reply With Quote
Old 09-20-2018, 06:41 PM   #29
jmodguy
Senior Member
 
jmodguy's Avatar
 
Join Date: Jul 2014
Location: Carmel, IN
Posts: 519
Default Re: #Northernfox Build

How did the riv-nuts work out? I was considering the same...
__________________
Jeff
KF 5
340KF
jmodguy is offline   Reply With Quote
Old 09-21-2018, 05:52 AM   #30
tracstarr
 
Join Date: Dec 2017
Location: Canada
Posts: 120
Default Re: #Northernfox Build

Quote:
Originally Posted by jmodguy View Post
How did the riv-nuts work out? I was considering the same...
Very easy, and one of those 'why wouldn't this be standard' moments. I'd post a pic once they are working again on this site.
tracstarr is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 11:56 PM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.